REHA TOWEL WARMER INSTALLATION MANUAL
This manual describes the steps required for the installation of Reha Havlupan towel warmers. Please follow each step carefully and follow the recommended safety instructions. Before starting the installation process, make sure that the necessary equipment and materials are complete.
Required Tools and Materials
– Drill and suitable drill bits
– Spirit level
– Screwdriver set
– Key set
– Tape measure
– Pencil
– Towel warmer wall mounting apparatus (supplied with the product)
– Screw anchors and screws (supplied)
– Teflon tape
– Pipe spanner
Preliminary Preparation
1. Check Box Contents: Open the product package and make sure that the parts inside the box are complete. All mounting apparatus and fasteners must be provided with the product.
2. Determine the Mounting Area: Select the wall where the towel warmer will be mounted. Make sure that the wall is solid and capable of supporting the towel warmer. Check that there are no obstacles in the area where the heating pipes pass.
3. Switch off the water supply: Switch off the water inlets of the system before starting the installation process. This will prevent any water leakage during installation.
Installation Steps
1. Marking of Wall Holes
– Determine the area on the wall where the towel rail will be mounted. Ensure the correct alignment of the towel rail using a tape measure and spirit level.
– Mark with a pencil the points where the towel warmer mounting apparatus will be placed. Make sure that these points are at the same level with the spirit level.
2. Hole Drilling Process
– Drill holes in the wall using a drill bit of suitable diameter at the points you have marked.
– Insert the dowels into the holes you drilled. Make sure that the dowels are fully seated on the wall.
3. Fixing the Mounting Apparatus
– Place the wall mounting brackets of the towel warmer on the dowels and tighten the screws.
– Make sure that the apparatus is securely mounted.
4. Mounting the towel warmer on the wall
– Carefully insert the towel rail into the wall mounting brackets. Make sure that the towel rail is hung straight and levelled when checked with a spirit level.
– Tighten the fixing screws on the mounting brackets. Check that the towel warmer is securely mounted on the wall.
5. Making Water Connections
– Install the appropriate fittings at the water inlet and outlet points of the towel warmer. Be sure to ensure water tightness by using Teflon tape.
– Make the water connections tightly with the help of pipe spanner. However, be careful not to over tighten, otherwise the fittings may be damaged.
6. Air Venting of the Towel Warmers
– Open the bleed valve located at the top of the towel warmer. This is necessary to prevent air accumulation inside the towel warmer.
– When water starts to flow from the bleed valve, close the bleed valve.
Final Checks and Testing
1. Open the plumbing: Reopen the water valves in your bathroom and check the water connections of the towel warmer. Check for any leaks.
2. Test the towel warmer: Switch on the heating system to check that the towel warmer is working properly. The surface of the towel warmer should heat evenly and there should be no water leakage at the connections.
3. Mounting Checks: Make sure all screws and connections are tight and the towel warmer is properly installed.
Maintenance and Cleaning Tips
Regular Cleaning:Clean the surface of the towel warmer regularly with a soft cloth. Do not use abrasive cleaners.
Bleeding: At the beginning of each heating season, check the air vent valve of the towel warmer and bleed the air if necessary.
Connection Checks: Check the water connections once a year and tighten the loosened parts.
Important Warnings
– Read all safety instructions before carrying out the installation.
– If electrical connection is required, have it done by an authorised electrician.
– If you encounter any problems with the product, please contact the authorised service.
Reha Havlupan provides comfort and aesthetics in your bathroom by offering quality and durable towel warmer solutions. By carefully following this installation guide, you can safely install your towel warmer and enjoy a warm environment in your bathroom.
This guide has been prepared to ensure easy and safe installation of Reha Havlupan products. Following each step carefully is important for both the correct completion of the installation and the long-lasting use of the product.